Pooldex

How to backwash a pool filter

To backwash a pool filter, turn the pump off, set the valve to BACKWASH, and run the pump for about 2 minutes until the water in the sight glass or waste line runs clear. Then turn the pump off, run RINSE for 30–60 seconds, and return the valve to FILTER. Do it when the pressure gauge reads about 8–10 psi above your clean reading, the trigger in Hayward's sand and DE filter manuals.

By Aliaksandr Rusinski · Published October 30, 2026 · Formulas: methodology (last changed October 7, 2026) · Share

On this page (9 sections)

Backwashing applies to sand and DE (diatomaceous earth) filters. Cartridge filters are cleaned by hand instead; see how to clean a pool filter.

What backwashing does

In normal FILTER mode, water flows down through the sand (or onto the DE-coated grids), and dirt stays behind. In BACKWASH, the valve reverses the flow: water goes up through the sand, lifts the trapped dirt, and carries it out the waste line. RINSE then runs water in the normal direction, still to waste, to settle the sand bed and flush out loose dirt so it doesn't blow back into the pool, as Hayward's manual explains.

A typical multiport valve has six positions:

Multiport valve positions
PositionWhat it does
FILTERNormal filtering and regular vacuuming
BACKWASHReverses flow through the filter and sends dirt out the waste line
RINSENormal flow direction, but to waste; settles the sand after a backwash
WASTE (or DRAIN)Bypasses the filter and sends water out: for lowering the water or vacuuming heavy debris, such as settled floc
RECIRCULATEBypasses the filter and returns water to the pool
CLOSEDShuts off flow. Never run the pump in this position.

Positions from Hayward and Intex manuals. Some filters have a two-position slide or push-pull valve instead: FILTER and BACKWASH only.

When to backwash

  • Hayward sand filters: when pressure rises 8–10 psi above the start-up (clean) reading.
  • Hayward ProGrid DE filters: 8–10 psi above the reading right after fresh DE.
  • Pentair Quad DE filters: about 10 psi above the "Original Starting Pressure," or when flow drops noticeably.
  • Intex sand filter pumps: when the needle moves farther into the yellow zone than its starting point after the first backwash of new sand.

Backwashing more often than the gauge calls for wastes water and the chemicals in it, so don't backwash on a fixed day. During the first cleanup of a new or very dirty pool, Hayward notes you may need to backwash more often. Readings that don't make sense are covered on pool filter pressure.

How to backwash a sand filter

These steps follow Hayward's sand filter manual. Your filter's own manual comes first.

  1. Turn the pump off. Hayward says to always shut off the pump before you move the valve, to avoid strain on the valve and pipes.
  2. Roll out the backwash hose (if you use one) from the waste port to an approved drain spot, and open any waste-line valve.
  3. Set the valve to BACKWASH. On a multiport valve, push the handle down before turning it.
  4. Start the pump and backwash for about 2 minutes, or until the water in the sight glass or out of the hose runs clear.
  5. Turn the pump off. Set the valve to RINSE.
  6. Run RINSE for about 30–60 seconds, until the water runs clear again.
  7. Turn the pump off, set the valve to FILTER, and restart. Note the new clean pressure.
  8. Top up the pool if the level dropped below the middle of the skimmer opening.

Intex sand filter pumps work the same way. Intex support says to turn the pump off before turning the valve, stop the backwash when clean water comes out of the drain, then rinse for at least 1 minute.

How to backwash a DE filter

A DE backwash flushes out the old DE along with the dirt, so you must recoat the grids afterward. From Hayward's ProGrid manual:

  1. Turn the pump off and set the valve to BACKWASH.
  2. Run the pump for about 2 minutes, or until the waste water looks clean.
  3. Turn the pump off, set the valve to RINSE, and run it for about 20 seconds.
  4. Turn the pump off, set the valve to FILTER, and restart.
  5. Add the amount of fresh DE your filter's label calls for, mixed with water, slowly through the skimmer.

Hayward warns not to run a DE filter for more than a minute or two without its DE coat, or the grids can be damaged. If your system has a separation tank, empty its bag after the backwash, as Pentair's Quad DE guide describes. If the pressure stays high right after recoating, the grids need a full hand cleaning; see filter cleaning.

Cartridge filters: no backwash

A cartridge filter has no BACKWASH position, and running water backward won't remove what's stuck in the pleats. Turn the pump off, release the pressure, remove the cartridge, and hose it off. Above-ground cartridge pumps from Intex and Bestway work the same way.

Where the backwash water goes

Backwash water is pool water plus dirt, so it contains chlorine and, in a salt pool, salt. Pentair's filter guides tell owners to check local codes and ordinances for backwash and DE disposal. Rules differ by city: some allow discharge to the yard, some require the sanitary sewer, and many restrict storm drains. Intex says not to drain pool water onto the lawn, because chlorine and salt can harm grass. Spent DE should not go down a storm drain. Ask your city or county before you lay out the hose.

After backwashing: refill and retest

Each backwash sends pool water to waste. Some chemicals leave the pool only with the water, so refilling with fresh water lowers them: stabilizer (cyanuric acid, CYA), salt, and calcium. That can help if CYA is too high (see how to lower CYA), but in a salt pool it slowly lowers salt, so check your pool salt level after a season of frequent backwashing.

Refill to the right line (pool water level), run the pump for a few hours, and test before adding chemicals.

Sand in the pool after backwashing? A little right after a backwash is usually leftover sand, so run RINSE longer next time. A steady trickle of sand at the returns can mean a broken lateral (the slotted arms at the bottom of the tank) or a worn standpipe. Turn the pump off and have the filter inspected; Hayward says repairs go to an authorized dealer or service center.

FAQ

How long do you backwash a pool filter?

About 2 minutes, or until the water in the sight glass or waste hose runs clear, per Hayward's sand and DE manuals. Then rinse: about 30–60 seconds for a Hayward sand filter, about 20 seconds for a ProGrid DE filter, and at least 1 minute on an Intex sand pump.

How often should you backwash a sand filter?

When the gauge reads about 8–10 psi above its clean reading, not on a fixed schedule. In a clean, lightly used pool, that can be every few weeks; after a storm or algae cleanup, it can be every few days.

Can you backwash a cartridge pool filter?

No. Cartridge filters have no backwash valve. Turn the pump off, release the pressure, and hose the cartridge off by hand.

Why is there sand in my pool after backwashing?

A small amount right after backwashing usually means the rinse was too short. Sand that keeps coming back can mean a cracked lateral or standpipe inside the tank, which needs a repair.

Does backwashing lower chlorine or salt?

It removes pool water, and with it some of every chemical in it. After you refill with fresh water, stabilizer, salt, and calcium are lower in proportion to how much water you replaced. Retest before adding chemicals.

Sources

  • Hayward, Pro Series high-rate sand filter manual S311SX/S360SX (8–10 psi, pump off before moving the valve, backwash about 2 minutes, rinse 1/2–1 minute, valve positions): hayward.com (PDF)
  • Hayward, ProGrid DE filter owner's manual (8–10 psi, backwash about 2 minutes, rinse 20 seconds, recoat with DE): hayward.com (PDF)
  • Pentair, Quad D.E. filter installation and user's guide (about 10 psi, local codes for backwash and DE disposal, separation tank): pentair.com (PDF)
  • Intex Support, Backwash for the sand filter pump: intexsupport.com
  • Intex, Sand filter pump valve positions: intexcorp.com (PDF)
  • Intex Support, Getting the pool ready for winter (local rules, not onto the lawn): intexsupport.com