Pooldex

How to clean a pool filter

Clean a pool filter when its pressure gauge reads about 8–10 psi above the reading it had when clean, the trigger Hayward and Pentair give in their manuals. Hose off a cartridge, backwash a sand or DE filter, and do a deeper clean (degreaser, then acid only if needed) when hosing or backwashing no longer brings the pressure back down.

By Aliaksandr Rusinski · Published October 30, 2026 · Formulas: methodology (last changed October 7, 2026) · Share

On this page (9 sections)

This guide covers all three filter types: cartridge, sand, and DE (diatomaceous earth). Backwashing has its own step-by-step page: how to backwash a pool filter. A hot tub filter is a different job, covered in hot tub filter cleaning.

When to clean: the pressure rule

Every filter maker we checked uses the same signal: a rise on the pressure gauge compared with the reading when the filter was clean. As dirt builds up, water has a harder time passing through, so pressure goes up and flow goes down.

  • Hayward sand filters (S311SX manual): backwash when pressure rises 8–10 psi above the start-up (clean) reading.
  • Hayward ProGrid DE filters: backwash when pressure rises 8–10 psi above the pressure right after adding fresh DE.
  • Pentair Clean & Clear cartridge filters: clean at about 10 psi above the "Original Starting Pressure" (Plus model) or 8–10 psi above it (RP model), or when flow drops noticeably.

So the first step is to know your clean number. Write it on a piece of tape next to the gauge right after a cleaning. If your pump has more than one speed, note the speed too, because Pentair points out that the starting pressure depends on pump speed. Normal readings and what high or low pressure means are on pool filter pressure.

Cleaning on a calendar instead of the gauge wastes water (sand and DE) or wears out cartridges faster. A new or very dirty pool may need cleaning every few days; a clean, lightly used pool can go weeks.

How to clean a cartridge filter

Cartridge filters are not backwashed. You take the cartridge out and rinse it. The steps below follow Pentair's Clean & Clear guides; check your own filter's manual for its lid and clamp details.

  1. Turn the pump off and switch off any timer or automation so it can't start while the filter is open.
  2. Open the air relief valve on top of the filter and wait until the gauge reads 0 psi. Never loosen the clamp or lock ring while the system is under pressure; Pentair warns that trapped air can blow the lid off.
  3. Open the drain and remove the lid, then lift out the cartridge.
  4. Hose it off with a garden hose and a straight-stream nozzle held at about a 45-degree angle, top to bottom, working between the pleats. Turn the cartridge as you go.
  5. Rinse out the tank and check the lid O-ring. Clean it and, if your manual says to, coat it with a silicone (not petroleum) lubricant.
  6. Reassemble, open the air relief valve, start the pump, and close the valve once a steady stream of water comes out.
  7. Write down the new clean pressure.

A spare set of cartridges makes this faster: swap in the clean set, and clean and dry the dirty set later.

Degreasing and acid soaking

Hosing removes dirt, not oils. Sunscreen, body oils, and lotions coat the fabric, and the pressure stops dropping after a rinse. Pentair's RP guide gives this deep-clean method:

  1. Degrease first. Soak the cartridge for at least 1 hour in a commercial filter cleaner, or in 1 cup of trisodium phosphate (TSP) or 1 cup of dishwasher detergent per 5 gallons of water. Rinse well.
  2. Acid soak only if minerals remain. For scale, iron, or calcium buildup, Pentair's Plus guide uses 1 part muriatic acid to 20 parts water in a plastic container: soak each end for about 10 minutes or until bubbling stops, then rinse.

The order matters. Pentair warns that acid soaking before you remove oils can permanently restrict flow and ruin the cartridge. Work outdoors, wear gloves and eye protection, and add acid to water, never water to acid. Dispose of the used solution as your local rules require.

Safety. Muriatic acid burns skin and eyes and releases strong fumes. Never mix acid with chlorine or with a chlorine-based cleaner: the two release chlorine gas. Keep children and pets away from the soaking bucket. If acid splashes on skin or in eyes, rinse with water for 15 minutes and call Poison Control at 1-800-222-1222. Always follow the product label. It is a violation of federal law to use a pesticide product in a manner inconsistent with its labeling.

How to clean a sand filter

Day to day, you clean a sand filter by backwashing: reversing the flow so dirt lifts out of the sand and goes out the waste line. Hayward's sand manual gives these numbers: backwash at 8–10 psi above clean, for about 2 minutes or until the sight glass runs clear, then rinse for about 30–60 seconds. The full steps are on backwashing a pool filter.

When backwashing stops working:

  • Pressure that rises again soon after a backwash is often a water problem, not a filter problem. Hayward's problem list says to check for algae and to check chlorine and pH first.
  • Crusted or caked sand. Hayward's manual says to check the top of the sand for a crust and to remove about 1 inch of sand if needed.
  • Chemical sand cleaners (often labeled "filter cleaner" or "sand filter cleaner") break down oils and scale in the sand bed. Use only as the product label directs; most are added through the skimmer or poured into the opened filter, left to soak, then backwashed out.
  • Old sand. Intex expects sand in its SX1500 pump to need replacing about every 5 years. Sand grains wear smooth over time and catch less dirt.

How to clean a DE filter

A DE filter traps dirt in a thin coat of DE powder on fabric grids. Cleaning it has two levels.

  1. Backwash, then recharge. Hayward's ProGrid manual says to backwash about 2 minutes or until the waste water runs clean, rinse about 20 seconds, then add fresh DE through the skimmer. Pentair's Quad DE guide does the same: backwash, restart, then add the amount of DE listed for your model. Dispose of spent DE as local codes require.
  2. Take it apart when backwashing isn't enough. If pressure stays high right after a fresh DE coat, the grids need a full clean. Hayward says to backwash first, turn off the power, open the air relief valve, drain the tank, lift out the grid assembly, and hose it inside and out, then brush gently. Do not pressure-wash grids; Hayward says it can damage them. A degreaser soak works on DE grids the same way as on cartridges.

How much DE your filter takes depends on its size; the table is on the pool filter size calculator page.

Above-ground pump cartridges (Intex, Bestway)

Small above-ground filter pumps clog faster because their cartridges are small. Intex support says to rinse the cartridge with a strong stream of water, from the inside, and to replace it regularly. Unplug the pump before you open the housing. Which cartridge fits your pump is on Intex filter cartridge types and the Bestway Flowclear filter guide.

When to replace instead of clean

  • The clean pressure keeps rising. If a cartridge you just cleaned and degreased still reads well above its new-cartridge baseline, it's worn out.
  • Damage: torn or flattened pleats, cracked end caps, or a cartridge that has gone soft.
  • Age. Pentair gives about 3 years as average cartridge life under normal conditions; heavy use, dust, and pollen shorten it.
  • DE in the pool after recharging usually means a torn grid or a bad seal.

A filter that is too small for the pump clogs fast no matter how well you clean it. Check yours with the filter size calculator.

Clean water also depends on chemistry. If the water stays dull or hazy with a clean filter, test chlorine and pH; see cloudy pool water. Filter care is one part of the weekly routine on how to clean a pool.

FAQ

How often should you clean pool filters?

Go by the gauge, not the calendar: clean when pressure is about 8–10 psi above your clean reading, which is the trigger in Hayward and Pentair manuals. Also do a full clean when you close the pool. Small above-ground cartridges may need a rinse every week or two in summer.

Can you clean a pool filter cartridge with vinegar or bleach?

The manuals we read don't list either one. Pentair lists a commercial filter cleaner, trisodium phosphate, or dishwasher detergent for oils, and diluted muriatic acid for minerals, in that order. Never combine an acid with a chlorine product.

Can I pressure-wash a pool filter cartridge?

Use a garden hose instead. Pentair's guide calls for a straight-stream garden hose nozzle, and Hayward warns that pressure washing can damage DE filter grids. A pressure washer can tear or fray filter fabric.

How do you chemically clean a sand filter?

Use a sand filter cleaner and follow its label, which usually means adding it to the filter, letting it soak, and then backwashing. If the top of the sand has formed a hard crust, Hayward's manual says to remove about 1 inch of sand.

When should you replace a pool filter cartridge?

When a clean, degreased cartridge still runs at a much higher pressure than it did new, or when the pleats or end caps are damaged. Pentair puts average cartridge life at about 3 years.

Sources

  • Pentair, Clean and Clear Plus cartridge filter installation and user's guide (clean at about 10 psi, hose at 45 degrees, acid soak 1:20 after removing oils, 50 psi maximum): pentair.com (PDF)
  • Pentair, Clean and Clear RP cartridge filter guide (8–10 psi, degreasing soak, 3-year average life): pentair.com (PDF)
  • Hayward, Pro Series high-rate sand filter manual S311SX/S360SX (8–10 psi, backwash and rinse times, crusted sand): hayward.com (PDF)
  • Hayward, ProGrid DE filter owner's manual (8–10 psi, backwash, manual cleaning, no pressure washing): hayward.com (PDF)
  • Pentair, Quad D.E. filter installation and user's guide (backwash, recoat with DE, DE disposal): pentair.com (PDF)
  • Intex Support, General pool water maintenance (rinse the cartridge, backwash a sand pump): intexsupport.com
  • Intex, SX1500 sand filter pump (sand replacement about every 5 years): intexcorp.com