How to floc a pool
Pool flocculant (floc) is an aluminum-based chemical that clumps the fine particles clouding your water so they sink to the floor, usually overnight; you then vacuum that layer out to waste, not through the filter. Use it only if your filter has a waste setting (most sand filters and diatomaceous earth, or DE, filters), because floc labels say not to use it when you can't vacuum to waste.
Always follow your product’s label directions. Pool and spa chlorine, bromine, shock, and algaecides are EPA-registered pesticides: use products labeled for pool or spa use, and don’t swim or soak until levels are within the limit on your product’s label. If this page and a label disagree, the label wins.
On this page (8 sections)
Floc is the fast, hands-on fix for heavily clouded water: one evening to dose, a night to settle, and a careful vacuum the next morning. It doesn't kill germs or algae and doesn't fix the cause, so it works alongside chlorine and water balance, not instead of them.
What floc is and how it works
Pool flocs are aluminum compounds. The products we checked use aluminum chloride, aluminum chloride hydroxide, or aluminum sulfate (alum). In the water, they gather the tiny particles that make water hazy into heavier clumps. One maker says the clumps sink to the pool floor "within hours." With the pump off, the clumps settle as a cloudy layer on the floor, and the water above them clears.
A clarifier does something different: it makes particles big enough for the filter to catch, and the filter does the work. That is why clarifier works with any filter and floc needs a waste line. The side-by-side choice is on clarifier vs flocculant.
When to use pool flocculant
- Use floc when the water is so cloudy you can't see the floor, the cause is fixed (chlorine and pH in range, algae dead), and you can vacuum to waste.
- Use clarifier instead for mild haze, with a cartridge filter, or when you can't leave the pump off overnight.
- Fix the cause first. If the water is cloudy because chlorine is low or algae is alive, floc only moves the problem to the floor. Start with cloudy pool water, or clearing a green pool if it is green.
- Pollen and fine dust that pass through the filter are a good fit for floc too: see pollen in a pool.
How to floc a pool, step by step
These steps combine the directions of two pool floc products (HTH Drop Out and Haviland Super Fall Out). Your product's label comes first, especially for the amount, the pH range, and the times.
- Test and adjust pH and alkalinity to the range on the floc's label. Floc works only in that range.
- Raise the water level to near the top of the skimmer opening. Vacuuming to waste removes water.
- Set the multiport valve to "recirculate," so water bypasses the filter.
- Add the label's amount for your gallons, the way the label says: spread over the surface, or poured slowly through the skimmer.
- Circulate for the time on the label (2 hours on one product, 4 on another), then turn the pump off.
- Leave the pool still while the clumps settle: 8–12 hours on the labels we read, longer for heavily clouded water. Don't run the pump and don't swim.
- Set the valve to "waste." Vacuum slowly, with long, gentle strokes, so the settled layer doesn't stir up.
- Top up the water as you go if the level drops near the skimmer. When the floor is clean, backwash (sand) or clean the filter (DE), and refill.
- Test and rebalance pH, alkalinity, and chlorine.
The right water level for your pump: pool water level. If pH needs adjusting before or after: lowering pH or raising pH.
Flocking a pool with a sand filter
A sand filter with a multiport valve is the easiest setup for floc, because it has both settings you need: recirculate while you dose, and waste while you vacuum. A DE filter with a multiport valve works the same way. If your sand filter has a push-pull valve instead, check whether it can send water straight to waste; if it can only backwash, vacuuming would push the floc through the sand.
Vacuuming the floc through the filter on "filter" clogs the sand or DE with the same particles you wanted out, and the water clouds up again. One alum floc label says: do not vacuum to the filter.
Cartridge filters: no waste setting
A cartridge filter has no waste setting, so the floc labels we read say to use a clarifier instead. Some owners send the vacuumed water straight out of the pool with a separate pump or a siphon hose. That is a workaround, not a label direction, and it is slow with a thick layer. For most cartridge pools, a clarifier is the practical choice.
When floc doesn't work
| What happened | Likely cause | What to do |
|---|---|---|
| Nothing settled | pH or alkalinity outside the label's range; pump ran during settling | Rebalance and dose again only if the label allows a second dose |
| Cloud comes back while vacuuming | Vacuuming too fast, or a stiff brush stirred the layer | Stop and let it settle again for a few hours |
| Water clouds again a day later | The cause wasn't fixed: low chlorine, algae, high pH | Test and fix chlorine and balance; see algae types if it turns green |
| Filter clogged fast | Floc was vacuumed through the filter | Backwash or clean the filter; vacuum to waste next time |
More product does not settle faster. We could not find a pool floc maker that explains what an overdose does, so use the amount on the label.
The Pooldex app doesn't dose floc, but it helps with the part that keeps the water clear afterward: enter a test after the cleanup, and it gives the chlorine and pH doses in order.
Safety. Aluminum sulfate floc is a skin and eye irritant (SDS): wear gloves and safety goggles. Don't mix floc with other chemicals, and store it away from chlorine products, dry and in its original container. No swimming while the floc is settling or before you vacuum. Always follow the product label.
FAQ
What is floc for pools?
Floc is a chemical, usually an aluminum compound, that clumps fine particles in cloudy water so they sink to the floor. You vacuum the settled layer out to waste, and the water above it is clear.
How long does it take flocculant to work?
Usually overnight. The labels we read call for 2–4 hours of circulation, then 8–12 hours with the pump off, sometimes longer for heavily clouded water.
Can I use flocculant with a cartridge filter?
The floc labels we read say no: a cartridge filter has no waste setting, and vacuuming floc through the cartridge clogs it. Use a clarifier instead, or remove the vacuumed water with a separate pump or siphon hose.
Can you floc a pool with a sand filter?
Yes, if the valve has recirculate and waste settings. Dose on recirculate, let it settle with the pump off, then vacuum on waste so the floc never goes through the sand.
Can you make homemade pool flocculant?
We don't recommend it. No pool chemical maker or public agency we found supports it, and grocery "alum" is usually potassium alum, not the aluminum sulfate in pool floc. Use a product labeled for pools.
Sources
- HTH, Drop Out flocculant (aluminum chloride, steps, vacuum to waste, cartridge filters): hthpools.com
- HTH, Cloudy pool water (clarifier vs floc, settling time): hthpools.com
- Haviland Super Fall Out flocculant label (aluminum chloride hydroxide, steps, settling time): poolweb.com
- Bio-Dex Alum flocculant directions (do not vacuum to the filter): sunplay.com
- Lawrason's AQUA FLOC safety data sheet (aluminum sulfate hazards and storage): PDF