How to lower CYA (cyanuric acid) in a pool
To lower CYA (cyanuric acid, also called stabilizer) in a pool, drain part of the water and refill with fresh water: going from 100 to 40 ppm takes about 60% of the water. In a 15,000-gallon pool, that is roughly 9,000 gallons.
Always follow your product’s label directions. Pool and spa chlorine, bromine, shock, and algaecides are EPA-registered pesticides: use products labeled for pool or spa use, and don’t swim or soak until levels are within the limit on your product’s label. If this page and a label disagree, the label wins.
Pooldex, free for iPhone: save your pool and products, get wait timers and a retest reminder, and keep a log of every test. No ads, no account. Download on the App Store
On this page (9 sections)
Draining and refilling is the only reliable way to lower CYA levels in a pool. The share of water to replace is (CYA now − target) ÷ (CYA now − CYA of your fill water). The calculator on this page does the math, including several smaller drains.
Drain calculator: current CYA, target, fill water CYA
Enter your CYA now, the level you want, the CYA in your fill water (usually 0, but test it if you use well water or a neighbor's pool), your volume, and the most you can safely drain at once. The calculator gives the share to replace in one drain and, if that is more than your limit, how many partial drains it takes. It also works for calcium hardness and salt, which only leave with water too.
Test first, carefully. Most CYA tests are unreliable above about 100 ppm, so dilute the sample 1:1 with tap water and double the result (PHTA). A draining decision based on a misread test is expensive.
| CYA now | One drain | Drains of 25% | Drains of 33% | Drains of 50% |
|---|---|---|---|---|
| 50 ppm | 20% | 1 | 1 | 1 |
| 60 ppm | 33% | 2 | 1 | 1 |
| 80 ppm | 50% | 3 | 2 | 1 |
| 100 ppm | 60% | 4 | 3 | 2 |
| 120 ppm | 67% | 4 | 3 | 2 |
| 150 ppm | 73% | 5 | 4 | 2 |
Counts are rounded up; the last drain can be smaller. Salt pools aiming for 70 ppm need less: from 100 ppm replace 30%, from 120 ppm about 42%.
Fill water matters. If your tap or well water has 5 ppm CYA, getting from 100 to 40 takes about 63% instead of 60%; at 10 ppm it takes about 67%.
Why CYA only leaves with water
Cyanuric acid is a stable compound. Sunlight doesn't break it down, normal chlorine levels barely affect it, and it doesn't evaporate: when water evaporates and you top up, the CYA stays and the level slowly rises. It leaves the pool only with the water itself, through splash-out, backwashing, overflow after heavy rain, and draining.
Why bother lowering it? CYA holds part of your chlorine in reserve, and the CDC's Model Aquatic Health Code (2024 Annex) ties the minimum chlorine to the CYA level. At 40 ppm CYA the minimum free chlorine is 3 ppm; at 100 ppm it is 7.5 ppm, above the 4 ppm swimming limit on many pool chlorine labels. That is why high-CYA pools turn green even when "the chlorine reads fine." See the numbers for your pool on pool chlorine levels and the background on what cyanuric acid is.
Partial drain vs repeated small drains
One larger drain uses the least water. Going from 100 to 40 ppm takes 0.6 of a pool volume in one drain.
Repeated smaller drains use more water for the same result, because each refill dilutes water that is already partly fresh. With 25% drains, 100 → 40 ppm needs a bit over three drains' worth, about 0.8 of a pool volume. With 33% drains, about 0.75. The advantage is less risk to the pool: many vinyl-liner and above-ground pools shouldn't be drained low (see below), so smaller steps may be the only option.
Other ways to "replace water" work the same way: a long backwash, vacuuming to waste, or letting rain overflow. They are only slower. Since calcium and salt also drop by the same share, retest them after the refill; if you need to lower calcium on purpose, see how to lower calcium hardness.
Do CYA reducers work? (evidence)
Short answer: sometimes, under narrow conditions, and we found no independent proof that they work reliably in home pools. Products sold as "CYA reducer" or "stabilizer reducer" use bacteria or enzymes that break cyanuric acid down. The science behind them is real: bacterial enzymes (cyanuric acid hydrolases) do degrade CYA. But a study in the Journal of Industrial Microbiology and Biotechnology (2022) found these enzymes were inactivated by chlorine at levels as low as a fraction of a ppm. The authors also wrote that no enzyme products were available for industrial application at the time. Their method needed the chlorine removed first.
What that means for a home pool: a reducer can only work in water with little or no chlorine, often warm, for days to weeks, during which your pool is unprotected and may grow algae. We found no independent, controlled test of consumer CYA reducers in residential pools, so we cannot say how reliable they are. If you try one, follow its label exactly, test CYA before and after with a diluted sample, and budget for a partial drain if CYA doesn't drop.
Prevent it: tablets add 0.6 ppm CYA per 1 ppm chlorine
Most high-CYA pools got there through chlorine that contains stabilizer. PHTA puts it at 0.6 ppm CYA for every 1 ppm of chlorine from trichlor tablets, and 0.9 ppm from dichlor. A pool that uses 2 ppm of chlorine a day on tablets alone adds about 36 ppm of CYA in 30 days. Ways to stop the buildup:
- Once CYA reaches your target, switch from tablets to liquid chlorine, bleach, or a salt cell.
- Shock with liquid chlorine or cal-hypo, not dichlor.
- Don't add stabilizer before the season if you'll use tablets anyway.
- Track it: test CYA monthly. The chlorine tablet calculator projects CYA week by week, and the stabilizer calculator shows how much to add if you are starting from low.
Safety: vinyl liners and groundwater
- Vinyl-liner pools. A liner that is exposed to air and sun can shrink or pull out of its track, and an old liner may not stretch back when refilled. Check your manufacturer's guidance before draining more than a small amount; if in doubt, use several smaller drains and refill promptly. For frame and steel-wall pools, see above-ground pool draining.
- Above-ground pools. The water holds the wall's shape. Follow the manual's limit on how low to drain.
- Inground pools and groundwater. An empty or nearly empty inground pool can be pushed up by groundwater after heavy rain or in areas with a high water table. Many have a hydrostatic relief valve, but if you are unsure, ask a local pool professional before draining deeply.
- Where the water goes. Local rules on draining pool water to the street or storm drain differ. Check with your city, and let chlorine drop before you drain.
Hot climates: lowering CYA in Phoenix, Las Vegas, and Texas
Desert and hot-climate pools reach high CYA faster: evaporation takes water but leaves stabilizer behind, and many owners run tablets all summer. The dilution math is the same everywhere, but heat changes how you drain.
- Don't leave surfaces dry in the sun. A vinyl liner exposed to air and sun can shrink, and that risk is higher in summer heat. Drain in smaller steps, or drain and refill at the same time, so the surface stays under water. Many owners in hot areas schedule big drains for the cooler months.
- Keep chlorine up while CYA is high. Until the drain is done, your minimum free chlorine follows your current CYA (7.5 ppm at CYA 100 in the CDC model code's table), which is above the 4 ppm swim limit on many labels. Lower CYA first rather than chasing that number.
- Check your city's drain rules first. The City of Phoenix, for example, says to drain to the sewer clean-out at your house with a submersible pump of about 700 gallons per hour (it gives 12 gallons per minute as the maximum). It also says not to drain into the street, alley, or other city right-of-way. Homes without a sewer clean-out need a permit to discharge clean pool water to the right-of-way, with chlorine below 1 ppm and flow below 50 gallons per minute. Discharging backwash water or water from salt water pools is prohibited. Other cities have their own rules.
- Texas cities, including San Antonio. Hot Texas summers, tablets, and evaporation push CYA up the same way. Water utilities set their own rules on where pool water may go, and drought stages can add limits. In San Antonio, ask the San Antonio Water System (SAWS) before a large drain. We could not find a current SAWS page with step-by-step draining rules, so get the answer from SAWS directly.
- Water-saving filtering. In some desert areas, mobile reverse osmosis (RO) services filter the pool water on site and return most of it. We could not confirm independent figures for how much CYA or water they save, so ask the provider for a CYA test before and after, in writing.
- Prevent it next season. Switch to liquid chlorine once CYA reaches your target, and test CYA monthly in summer; the CYA buildup calculator shows when tablets will push you over. More heat-wave advice is on pool care in hot weather.
After refilling, circulate for a few hours and retest everything: CYA, chlorine (your minimum drops with CYA), pH, alkalinity, and calcium.
FAQ
What causes pool stabilizer to be high?
Mostly trichlor tablets and dichlor shock, which add CYA every time you chlorinate. Other causes: adding stabilizer again before the first dose dissolved, and very little water replacement (dry climate, no backwashing, pool covered all season). Evaporation makes it worse because top-up water replaces the water but the CYA stays.
What happens if cyanuric acid is too high?
More of your chlorine is held in reserve, so the same reading kills germs and algae more slowly. The minimum free chlorine rises with CYA: 3 ppm at 40, 7.5 ppm at 100. Once CYA is above 50 ppm, that minimum is higher than the 4 ppm swim limit on many chlorine labels, which is why high-CYA pools turn green or cloudy while "the chlorine reads fine."
Can you lower CYA without draining the pool?
Not reliably. CYA leaves only with water: backwashing, splash-out, rain overflow, or a drain. Bacterial "CYA reducer" products need low chlorine to work, and we found no independent test of them in home pools. Reverse osmosis filtering services are an option in some areas. A partial drain is the predictable method.
Does baking soda lower cyanuric acid in pools?
No. Baking soda raises total alkalinity and nudges pH up. It doesn't react with cyanuric acid, so CYA stays the same.
Does shock lower cyanuric acid?
No. Chlorine at shock levels barely affects CYA. Dichlor shock raises it: about 0.9 ppm CYA for every 1 ppm of chlorine. Cal-hypo and liquid chlorine add none, so they are the forms to use when CYA is already high.
How to lower cyanuric acid in pool naturally?
There is no reliable natural method beyond water replacement: rain overflow, splash-out, and backwashing all lower CYA a little. Sunlight and time do not. Bacterial products exist, but we found no independent evidence that they work reliably in home pools. A measured partial drain is faster and more predictable.
Sources
- CDC, Model Aquatic Health Code 2024, Annex (CYA and chlorine): cdc.gov (PDF)
- PHTA fact sheet, Dichlor (CYA added per ppm of chlorine): phta.org
- A procedure for removal of cyanuric acid in swimming pools using a cell-free thermostable cyanuric acid hydrolase, J Ind Microbiol Biotechnol 49(2), 2022: pmc.ncbi.nlm.nih.gov
- Pentair, IntelliChlor SCG Quick Start Guide and Tips (stabilizer 30–50 ppm): PDF
- Hayward, AquaRite manual: PDF
- City of Phoenix Water Services, Draining and backwashing your pool (read 2026-10-11): phoenix.gov
- Drain formula and test cases: our methodology page