Pool chlorinator and feeder settings
A swimming pool chlorinator is a closed canister of slow-dissolving trichlor tablets plumbed into the return line, with a dial that sets how much water flows past the tablets. There is no universal correct setting: Hayward's manual says to test chlorine daily and turn the dial up or down until free chlorine holds steady at your target.
Always follow your product’s label directions. Pool and spa chlorine, bromine, shock, and algaecides are EPA-registered pesticides: use products labeled for pool or spa use, and don’t swim or soak until levels are within the limit on your product’s label. If this page and a label disagree, the label wins.
Pooldex, free for iPhone: save your pool and products, get wait timers and a retest reminder, and keep a log of every test. No ads, no account. Download on the App Store
On this page (10 sections)
The calculator below estimates how many tablets your pool uses per week from its size and daily chlorine loss, and how fast tablets raise stabilizer. That tells you how often you'll refill the feeder and when to switch to another chlorine.
What a pool chlorinator does
Inside the canister, water flows over the tablets and slowly dissolves them. The dial (a flow control valve) sets how much water passes through, so a higher number dissolves tablets faster and adds more chlorine. Compared with a floating dispenser or tablets in the skimmer, a feeder gives steadier output that you can adjust, and the tablets are out of reach of swimmers.
It is not a salt chlorine generator. A salt cell makes chlorine from salt using electricity; a feeder only dissolves tablets you load. For salt systems, see salt water pool care.
Inline vs offline feeders
| Inline (CL100, CL200) | Offline (CL110, CL220) | |
|---|---|---|
| How it connects | Built into the return pipe; all the water goes through the feeder body | Mounted beside the pipe; small tubes take some water in and send it back |
| Where | In the return line after the heater, or after the filter if there is no heater | Inlet tube after the pump and before the filter; outlet after the heater, or after the filter if there is no heater |
| Check valve | Recommended in the line (built into the CL100) | Included on the outlet |
| Good for | New equipment pads or re-plumbing | Adding a feeder to existing plumbing |
From Hayward's CL100/110/200/220 owner's manual. Other brands work the same way; follow your own feeder's manual.
Where it goes in the plumbing
The feeder must be the last piece of equipment before the water returns to the pool. Hayward's manual says to install it after the heater, because concentrated chlorine flowing through a heater or filter can damage them. It also recommends a corrosion-resistant check valve to keep chlorine gas from flowing back toward the equipment when the pump shuts off, and warns never to install a feeder directly into copper plumbing.
Installing a feeder means cutting and gluing pipe or drilling into it. If you're not comfortable with that, have a pool technician do it. If any wiring or bonding near the equipment needs to change, that's a job for a licensed electrician.
Setting the dial from your chlorine test
Hayward says the right setting depends on usage, temperature, and sunlight, and that you'll have to experiment at first. A practical way to find it:
- Start with balanced water and chlorine already in range. The feeder keeps chlorine up; it isn't meant to raise it quickly. Bring free chlorine (FC) to your target first with liquid chlorine. The minimum depends on your stabilizer level; see pool chlorine levels.
- Load the feeder with slow-dissolving trichlor tablets only, and set the dial to a middle setting.
- Test FC at the same time every day for a few days, with the pump on its normal schedule.
- Adjust in small steps. FC falling day to day: turn the dial up one step. FC climbing: turn it down one step. Wait a full day between changes.
- Re-check after big changes in weather, swimmers, or pump hours. Hot weather and more swimmers use more chlorine.
The dial only works while water flows. Fewer pump hours mean less chlorine, whatever the dial says. For comparison, Hayward lists the CL200's maximum output at 2.30 lb of chlorine per day at the full pool setting.
Refilling it safely
The canister holds strong chlorine water and can be under pressure. Hayward's refill steps:
- Turn off the pump and any timer.
- Turn the feeder's dial to OFF and make sure its return line to the pool is open.
- Wait one minute for pressure to release before opening the lid. If the feeder sits below water level, close the isolation valves first.
- Open the lid without leaning over it, add slow-dissolving trichlor tablets, and close it.
- Reopen any valves, set the dial, and restart the pump.
Safety. Use only the tablets your feeder's manual names. Hayward warns that mixing chemicals or using fast-dissolving tablets in its feeder can cause a fire or explosion: never put calcium hypochlorite (cal-hypo), shock, or any other chlorine in a trichlor feeder, even as leftover dust in a scoop. Don't breathe the fumes when you open the lid, and wear eye and skin protection. Hayward also says never to add other chlorine, pH adjusters, shock, or algaecide through the skimmer; add them directly to the pool water. Store tablets as described in how to store pool chemicals. Always follow the product label. It is a violation of federal law to use a pesticide product in a manner inconsistent with its labeling. Poison Control: 1-800-222-1222.
Floating dispensers
A floating chlorine dispenser (a "floater") is the simplest feeder: tablets sit in a floating cage with adjustable vents. It needs no plumbing and works in above-ground pools, but output depends on where it drifts and how warm the water is. If it gets stuck at the steps or in a corner, it can leave concentrated chlorine in one spot, which can fade or weaken a vinyl liner. Tie it off or check it daily, keep it away from children, and remove it before swimming if the tablet label says to. More about floaters, skimmers, and feeders is on the chlorine tablets calculator page.
Tablets raise stabilizer
Trichlor tablets are "stabilized" chlorine: every dose also adds stabilizer (cyanuric acid, CYA). CYA leaves the pool only with water, so a feeder running all season keeps pushing it up, and the chlorine level you need rises with it. That's the main limit of tablet feeders. Watch CYA with monthly tests and the CYA buildup calculator. When CYA reaches 30–50 ppm, many owners turn the feeder down and switch daily chlorine to liquid chlorine. If it's already too high, see how to lower CYA. Tablets also lower pH slowly over time; the trade-offs are in trichlor vs dichlor.
Winter and long pump stops
- Before stopping the pump for a long time, Hayward says to set the dial to zero. During backwash and periods with no flow, gas and concentrated chlorine can build up in the feeder and enter the pool when flow restarts. Keep backwash time short, and don't let anyone swim until full flow is back.
- Winterizing: where it freezes, remove all tablets and pieces, drain the feeder through its drain plug, rinse it with water, and close it up (Hayward). The rest of the plumbing is covered in how to blow out pool lines for winter.
- Vacuuming: close the feeder's valve so sediment doesn't clog it.
- O-ring: lubricate the lid O-ring only with the lubricant the manual names. Hayward says never to use petroleum-based lubricants.
FAQ
What is a swimming pool chlorinator?
A closed canister of slow-dissolving chlorine tablets, plumbed into the return line after the filter and heater. A dial sets how much water flows past the tablets, which sets how much chlorine goes into the pool while the pump runs.
What number should I set my pool chlorinator to?
There's no standard number. Start in the middle, test free chlorine daily at the same time, and turn the dial one step at a time until the reading holds steady at your target. Hayward's manual describes this trial-and-error approach.
What is the difference between an inline and an offline chlorinator?
An inline chlorinator is part of the return pipe, and all the water flows through it. An offline chlorinator sits beside the pipe and connects with small tubes, so it's easier to add to an existing pool.
Can I put shock or cal-hypo in a tablet chlorinator?
No. Hayward warns that mixing chemicals or putting cal-hypo or other chlorine in a trichlor feeder can cause a fire or explosion. Use only the tablet type your feeder's manual names, and add shock directly to the pool water.
Is a floating chlorine dispenser as good as an inline feeder?
It costs less and needs no plumbing, but its output is less steady and harder to control, and it can leave strong chlorine in one spot if it gets stuck. Both add stabilizer with every tablet.
Sources
- Hayward, CL100/CL110/CL200/CL220 automatic chlorine feeders owner's manual (tablets, installation, check valve, dial adjustment, refill steps, no-flow warning, CL200 output, winterizing): hayward-pool-assets.com (PDF)
- CDC, Model Aquatic Health Code 2024, Annex (chlorine and cyanuric acid): cdc.gov (PDF)
- CDC, Store pool chemicals safely (poster): cdc.gov (PDF)