Pooldex

White water mold in a pool

White water mold is a slimy white or gray growth that looks like wet tissue paper floating in the water or stuck behind ladders, in the skimmer, and in the filter. To get rid of it, clean every surface and the filter at the same time as you raise chlorine to the shock amount on your product's label, because chlorine alone can't reach growth hidden inside its protective slime (biofilm).

By Aliaksandr Rusinski · Published October 30, 2026 · Formulas: methodology (last changed October 7, 2026) · Share

Always follow your product’s label directions. Pool and spa chlorine, bromine, shock, and algaecides are EPA-registered pesticides: use products labeled for pool or spa use, and don’t swim or soak until levels are within the limit on your product’s label. If this page and a label disagree, the label wins.

Pooldex, free for iPhone: save your pool and products, get wait timers and a retest reminder, and keep a log of every test. No ads, no account. Download on the App Store

On this page (8 sections)

Despite the name, there is no agreed definition of "white water mold." Pool industry sources describe it as a fungus-like growth; others call it a biofilm of bacteria and fungi. The CDC doesn't use the term. What matters for cleanup is the same either way: it lives in a slimy film, and the CDC's model code notes that chlorine is generally ineffective against germs inside a biofilm. Scrubbing breaks the film so chlorine can work.

How to tell white water mold from other white stuff

White water mold vs other white material in a pool
What it isHow it looks and feelsWhere you find it
White water moldSoft, slimy, gray-white clumps or strands like wet tissue paperBehind ladders and steps, in the skimmer, light niche, pipes, and filter; floating bits after a backwash or a start-up
Scale flakesHard, thin, chalky flakes that don't smearNear returns, on the floor, from a salt cell or heater: calcium scale
Plaster dustFine powder that settlesA new or replastered pool
Pink slimeSlick pink or reddish filmThe same hiding places; often grows alongside white water mold: pink slime
Slimy walls with no visible colorA slick feel when you brush the wall or floorShady walls and the floor: early biofilm or algae; see pool algae types

Check the filter. White slime in a cartridge's pleats, or white strands in a sand filter's top layer, is a strong sign. Clumps that appear right after you open the pool or turn on the pump usually come from the pipes.

What causes white water mold

  • Low or uneven sanitizer. Biofilm starts where chlorine runs low for a while, such as during a vacation, a broken feeder, or a stretch of low free chlorine for your stabilizer level.
  • Dead spots. Behind ladders and steps, inside the light niche, and in pipes with little flow, the water barely moves.
  • Surfaces that never get brushed. Ladder treads, toys, floats, the skimmer, and the filter give it a place to hold on.
  • Biguanide (PHMB) pools. One manufacturer's technical staff links white water mold to low biguanide or hydrogen peroxide levels and poor circulation.

The CDC's model code adds that pieces of biofilm break off and spread through the system. That is why white water mold comes back after a cleanup that skips the filter or the pipes.

How to get rid of white water mold

Do all of these steps in the same cleanup. Cleaning the walls but not the filter, or shocking without brushing, leaves a source behind.

  1. Take out removable ladder parts, toys, floats, and cleaner hoses. Scrub them with a brush and a household cleaner, rinse, and let them dry in the sun.
  2. Test free chlorine (FC), pH, and stabilizer (CYA). Bring pH to 7.4–7.6 so chlorine works well.
  3. Brush every surface: walls, floor, steps, behind the ladder, the skimmer, and the light niche. The goal is to break the slime film.
  4. Add a chlorine product labeled for shocking pools, at the amount on its label for your gallons. Never go above the label amount.
  5. Run the pump day and night so treated water moves through the pipes and filter.
  6. Clean the filter. For a cartridge, the CDC model code describes rinsing, degreasing, and then soaking in household bleach diluted in water (1 quart per 5 gallons) for one hour. For sand or DE (diatomaceous earth) filters, follow the filter's manual and a filter cleaner's label. If slime keeps showing up in the media, replace it.
  7. Brush every day and keep free chlorine in your normal range. If new slime appears, repeat the brushing and the label's shock dose, as often as the label allows.
  8. Clean the filter one more time at the end. Debris from the cleanup collects there.

The chlorine range for your stabilizer level, before and after the cleanup, is in the calculator below. It shows your minimum and target free chlorine; for the shock step itself, use the amount on your product's label.

Chlorine level calculator

Inputs
ppm
ppm

Result for example values. Enter your own numbers.

Minimum FC
3 ppm
Target range
3–5 ppm
Shock
Follow your product’s label directions
Active chlorine (HOCl) at the low target, rough estimate
≈ 0.03 ppm (at pH 7.5)

Pool product labels (EPA) often say not to swim above 4 ppm. The CDC model code links the minimum to CYA. Keep CYA at 30–40 ppm so both fit.

Save to my pool in the app

Estimates, not guarantees. Always follow the product label. How we calculate

Biguanide pools: don't add chlorine

If your pool uses a biguanide (PHMB) system, chlorine is not compatible with it. A manufacturer's technical services lead recommends a chlorine-dioxide product made for biguanide pools and a flush of the plumbing. Use only products from your biguanide system's line, as their labels direct, or convert the pool with the maker's process.

White water mold in a hot tub

In a hot tub, white water mold usually lives in the pipes, and it shows up as white flakes or strands that blow out of the jets. Draining alone won't remove it:

  • Before you drain, add a line flush product and run the jets as its label directs. Line flush products are made to break biofilm loose from the pipe walls. Steps: how to flush hot tub lines.
  • Drain, then scrub every surface. The CDC's hot tub guidance for operators says to scrub all surfaces each time the tub is drained.
  • Clean or replace the filters: hot tub filter cleaning.
  • Refill, balance, and keep sanitizer in range from the first day.

How to keep it from coming back

  • Hold free chlorine in range for your stabilizer level, every day: pool chlorine levels. Chlorine that dips low for days lets biofilm restart. If chlorine keeps disappearing, see why a pool won't hold chlorine.
  • Brush weekly, including behind ladders and inside the skimmer.
  • Clean the filter on schedule.
  • Dry what you can. The CDC's model code notes that drying is one way to control biofilm. Let toys, floats, and the solar cover dry out between uses.
  • Run the pump long enough to move all the water through the filter every day.

The Pooldex app keeps a log of every chlorine test. A run of low readings before white water mold appears tells you where to look next time, and test reminders help keep chlorine from dipping.

Safety. Never mix chlorine with acid or with other chemicals, including when cleaning filters. Rinse the filter well before and after any soak. Wear gloves and eye protection. No swimming until chlorine is back at or below the swim limit on your product's label. Always follow the product label. It is a violation of federal law to use a pesticide product in a manner inconsistent with its labeling.

FAQ

What kills white water mold in a pool?

Chlorine at the shock amount on your product's label, but only together with brushing every surface and cleaning the filter. Without breaking up the slime, chlorine can't reach the growth underneath.

Is white water mold harmful to humans?

The CDC doesn't describe white water mold. It does say that germs such as Pseudomonas and Legionella can live in biofilm and are harder for disinfectants to kill. Treat any slime as a cleaning problem, and keep chlorine in range.

What causes white water mold in a pool?

Low or uneven sanitizer, water that doesn't move behind ladders and in pipes, and surfaces that never get brushed. Once it forms a slimy film, it protects itself from chlorine.

Will algaecide kill white water mold?

Only if the algaecide's label lists it, and most labels list algae only. Brushing, chlorine at the label's shock amount, and a clean filter are what remove it.

Can white water mold grow in a hot tub?

Yes, usually in the pipes, where it comes out as white flakes. Use a line flush product before you drain, then scrub the shell and clean or replace the filters.

Sources

  • CDC, Model Aquatic Health Code, Annex (biofilm, chlorine in biofilm, drying, cartridge filter cleaning): cdc.gov (PDF)
  • CDC, Controlling Legionella in hot tubs (scrub all surfaces each drain): cdc.gov (PDF)
  • CDC, Swimming-related diseases (biofilm, Pseudomonas, Legionella): archive.cdc.gov
  • CDC MMWR, Outbreaks associated with treated recreational water, 2000–2014: cdc.gov
  • Water Conditioning and Purification, Eliminating mold and slime in swimming pools (BioGuard technical services): wcponline.com
  • SpaGuard System Flush product page (biofilm in spa pipes): leisuretimeinc.com