Calcium scale and nodules in a pool
A white crust at the waterline is usually calcium scale, small raised white bumps on plaster are usually calcium nodules, and loose white flakes usually come from a salt cell, a heater, or new plaster. Scale is a water-balance problem you can prevent by keeping the saturation index (LSI) between −0.3 and +0.3 (CDC model code); nodules are a plaster defect that needs a plaster professional.
Always follow your product’s label directions. Pool and spa chlorine, bromine, shock, and algaecides are EPA-registered pesticides: use products labeled for pool or spa use, and don’t swim or soak until levels are within the limit on your product’s label. If this page and a label disagree, the label wins.
Pooldex, free for iPhone: save your pool and products, get wait timers and a retest reminder, and keep a log of every test. No ads, no account. Download on the App Store
On this page (8 sections)
All of these are forms of calcium carbonate, the same mineral, but they have different causes and different fixes. Find yours in the table first, then go to its section.
Which white deposit is it?
| What you see | Where | Likely cause | What to do |
|---|---|---|---|
| White or gray crust, rough to the touch | Tile at the waterline, spillways, fittings | Calcium scale from scaling water (high LSI) and evaporation | Balance the water; remove with a product labeled for scale |
| Raised white bumps, often over a crack or pinhole | Plaster walls or floor | Calcium nodules: water leaking out from behind the plaster | Plaster professional; water balance won't fix it |
| Thin white flakes floating or settling | Near the returns, floor | Scale from a salt cell or a heater, breaking loose | Inspect and clean the cell; check heater and water balance |
| Fine white dust on the floor | A new or freshly replastered pool | Plaster dust from curing | Brush and filter as the plasterer's start-up directions say |
| Greasy gray line that smears | Waterline | Body oils, sunscreen, and dirt, not scale | Scum line cleanup |
| Slimy white clumps like wet tissue | Walls, behind ladders, in the filter | Not calcium: a growth of microorganisms | White water mold |
A quick test: scale is hard and doesn't wipe off. A scum line smears under a finger. Slime is soft and slippery. Colored stains (brown, blue-green, purple) are usually metals: see pool stains.
Calcium scale: why it forms and how to stop it
Water can hold only so much calcium carbonate. The CDC's model code explains that the saturation index rises as temperature, alkalinity, pH, and calcium hardness rise. When the index is high, calcium comes out of the water as scale, which the code describes as white or lightly colored rough blotches. It also builds up in pipes and filters, where it restricts flow, and on heater parts.
Enter your readings below. The calculator shows your LSI and whether the water leans toward scaling or corrosion. The CDC model code recommends −0.3 to +0.3 and prefers a slightly positive number to a negative one, because corrosion causes permanent damage.
- High pH is usually the quickest number to change, and it moves the LSI directly: how to lower pH.
- High alkalinity keeps pushing pH up: lowering total alkalinity.
- High calcium hardness only comes down by replacing water: how to lower calcium hardness. Target ranges by surface are on calcium hardness.
- Heat and evaporation raise scaling risk. In summer and in heated pools, check the LSI more often.
Scale inhibitors (sequestrants) hold calcium in solution so it is slower to deposit. They don't lower calcium hardness, and one maker says its product "is not a replacement for balancing your water." Dose them by the label.
Pool tile cleaning: removing scale at the waterline
Waterline scale builds up where water evaporates and leaves minerals behind. How to remove it depends on the tile:
- First, balance the water. Otherwise new scale forms as fast as you remove the old.
- Light scale on ceramic or stone tile: a pumice stone or pumice scouring stick, kept wet, works on many tiles. Pumice makers say not to use it on glass tile, fiberglass, or plastic. Test a hidden spot first.
- Tile and scale cleaners: use only a product labeled for pool tile scale, exactly as its label directs. Some are acid-based: never mix them with chlorine products.
- Heavy scale or glass tile: tile cleaning services often use media blasting. The right media depends on the tile, so this is a job for a professional.
We don't give directions for acid-washing plaster or tile. Done wrong, it etches the surface and can release dangerous fumes; ask a pool professional.
Calcium nodules in pool plaster
Calcium nodules are hard, raised white bumps, often with a small crater or a crack under them. A study in the Journal of the Swimming Pool and Spa Industry explains how they form. Pool water gets into a gap behind the plaster through a hairline crack or pinhole. It picks up calcium hydroxide from the cement and seeps back out, where it turns into calcium carbonate on the surface. The gaps come from plaster that has come loose from the wall (delamination), heavy cracking, or poorly mixed spots.
- Water balance won't fix nodules. They come from inside the plaster, not from the water.
- Grinding one off removes the bump, not the cause. As long as water can reach the gap behind it, it can grow back.
- Call a plaster professional. The fix is usually to remove the loose plaster around the nodule and repair it. A pro can also tell you if the problem is widespread.
- New pool? Nodules in a new plaster finish may be a warranty question. Take photos and contact your builder.
White flakes in the pool
- Salt cell: Hayward says scale forms first on the salt cell plates as light-colored, crusty, or flaky deposits. Pieces can break off and blow out of the returns. Inspect the cell about every 3 months or 500 hours, and clean it as the manual says: how to clean a salt cell.
- Heater: unbalanced water can leave scale in a heater's heat exchanger tubes, and one heater maker says damage from unbalanced water isn't covered by its warranty. We could not confirm that heater scale shows up as flakes in the pool, but if your flakes appear after the heater runs, have it checked.
- Calcium dust in a new pool: fresh plaster releases calcium hydroxide as it cures, mostly in the first 1–2 weeks. Brushing and filtering it out is part of plaster start-up: new pool start-up.
White spots on pool plaster
White spots that are flat and don't feel raised are often scale spots, plaster dust that set before it was brushed off, or uneven color in the plaster finish. Raised spots over a crack are nodules. If the spots are rough and grow over the season, check your LSI. If they stay the same size and are flat, they are probably part of the finish. For cloudy water from the same causes, see cloudy pool water.
In the Pooldex app, calcium hardness is part of a pool test, and the app shows a scale-risk line with the LSI for your latest reading. The history shows whether your water has been leaning toward scale for weeks, not just today.
Safety. Tile and scale cleaners can be acidic: wear gloves and eye protection, never mix them with chlorine, and rinse tools before using another product. Turn off the pump and power before you remove a salt cell. Always follow the product label. It is a violation of federal law to use a pesticide product in a manner inconsistent with its labeling.
FAQ
What are calcium nodules in a pool?
Hard white bumps on plaster where water seeps through a crack or pinhole from a gap behind the plaster, carrying calcium out to the surface. They are a plaster defect, so a plaster professional needs to repair the area.
Why are there white flakes in my pool?
Usually scale breaking off a salt cell's plates, or sometimes from a heater. In a new pool, it can be plaster dust. Check the cell, then check your water balance with the LSI.
How do you get calcium scale off pool tile?
Balance the water first. Then use a wet pumice stone on ceramic or stone tile (not glass tile), or a product labeled for pool tile scale, exactly as the label says. Heavy scale or glass tile is a job for a tile cleaning professional.
How do I keep calcium scale from coming back?
Keep the LSI between −0.3 and +0.3, mainly by holding pH at 7.4–7.6 and alkalinity in range. Replace water if calcium is too high. A scale inhibitor can help, but it doesn't replace water balance.
Sources
- CDC, Model Aquatic Health Code, Annex (saturation index, −0.3 to +0.3, scale): cdc.gov (PDF)
- Skinner and Hales, Calcium nodules, Journal of the Swimming Pool and Spa Industry 3(2), 1998: PDF
- Hayward, H100ID1 heater manual (scale in heat exchanger tubes, warranty): PDF
- Hayward, How to clean your salt chlorinator cell (scale on cell plates, inspection interval): hayward.com
- Orenda, SC-1000 (scale control is not a replacement for water balance): orendatech.com