Pooldex

Pool test strips: how to read them

To read pool test strips, dip the strip for the time on your bottle, hold it flat, and match each pad to the color chart in the shade, before the reading time runs out.

By Aliaksandr Rusinski · Updated October 30, 2026 · Formulas: methodology (last changed October 7, 2026) · Share

Always follow your product’s label directions. Pool and spa chlorine, bromine, shock, and algaecides are EPA-registered pesticides: use products labeled for pool or spa use, and don’t swim or soak until levels are within the limit on your product’s label. If this page and a label disagree, the label wins.

Pooldex, free for iPhone: save your pool and products, get wait timers and a retest reminder, and keep a log of every test. No ads, no account. Download on the App Store

On this page (9 sections)

Read it in shade rather than direct sun. A strip reads in steps (for example, free chlorine 0, 0.5, 1, 3, 5, 10 ppm), so treat the result as a range and use a drop kit to confirm borderline readings.

Step by step: dip, wait, read

  1. Check the bottle. Look at the expiration date and make sure the cap was closed tightly. Strips that picked up moisture give wrong colors before you even dip them.
  2. Take the sample from the right spot. About elbow deep, away from return jets, the skimmer, and any chlorine floater, with the pump running and at least 30 minutes after you last added chemicals.
  3. Dip with dry hands. Take out one strip, close the cap right away, and dip for exactly as long as your bottle says. Brands differ, so don't rely on another brand's timing.
  4. Hold it flat, pads up. Don't shake it hard or hold it upright; otherwise, color from one pad can run into the next.
  5. Read inside the time window. Some brands read all pads at once; others read chlorine first and the rest after a wait. Colors keep changing after the window, so a strip read late gives a wrong result.
  6. Use good light. Open shade or indirect daylight is best. Direct sun, yellow porch lights, and phone flashlights all shift colors.
  7. Write it down or enter it. Note each value (or "between 1 and 3") with the date. A log is how you see trends, such as how fast your chlorine drops.

Strips do expire. AquaChek, for example, says strips have a definite shelf life, should not be used past the date, and should be stored at room temperature in low humidity with the cap on tight. If a bottle sat in a hot shed all summer, buy a new one.

Test strip steps: dip for the time on your bottle, hold it flat with pads up, and read against the chart in the shade before the time window ends.
Timing matters: dip and read for exactly the times on your own bottle, because brands differ.

Each pad explained: a typical strip chart

Most pool strips have four to seven pads. The steps below are typical color blocks on common bottles, not any one brand. Your chart may use different steps, so always compare with your own bottle.

Generic pool test strip color chart with six pads (free chlorine, total chlorine, pH, alkalinity, hardness, stabilizer), target blocks outlined, and four steps for reading a strip.
Strip colors come in steps, so treat each pad as a range and confirm borderline results with a drop kit.
Common strip pads, typical color steps and what to aim for
PadTypical steps on the chartAim forIf it's off
Free chlorine (FC)0 · 0.5 · 1 · 3 · 5 · 10 ppm2–4 ppm without stabilizer; about 3–5 ppm at CYA 40Add chlorine; the minimum depends on your CYA
Total chlorine (TC)same steps as FCEqual to FC, or less than 0.5 ppm above itA gap means combined chlorine: see FC vs TC
pH6.2 · 6.8 · 7.2 · 7.5 · 7.8 · 8.47.4–7.6Acid to lower it, soda ash to raise it
Total alkalinity (TA)0 · 40 · 80 · 120 · 180 · 240 ppm80–120 ppmBaking soda to raise, acid plus aeration to lower
Total hardness (reads close to CH)0 · 100 · 250 · 500 · 1,000 ppm200–400 ppm for plaster; 150–250 ppm for vinyl or above-groundCalcium chloride to raise; only fresh water lowers it
Stabilizer (CYA)0 · 30 · 50 · 100 · 150 · 300 ppm30–50 ppm (60–80 with a salt system)Stabilizer to raise; only draining lowers it

Targets are our calculator defaults. The full list with sources is the pool chemistry chart. Hardness pads on strips usually read "total hardness," which includes magnesium, so they can read a little higher than a calcium-only drop test.

Two pads need extra care. The pH pad is unreliable when chlorine is very high: strong chlorine bleaches the indicator, so after a shock, wait until FC is back under 10 ppm before trusting pH (PHTA). CYA pads are the least precise on most strips because the steps are far apart. A reading of "50" can mean anything between the neighboring blocks. For more on each value, see the pH levels and alkalinity levels pages.

Which pool test strips to buy (3-way, 6-way, 7-way, salt, CYA)

Bottles are usually sold by how many pads each strip has. Read the list of tests on the label, not the number on the front, and buy the strip that covers what you actually dose:

  • 3-way or 4-way strips usually read free chlorine, pH, and total alkalinity, sometimes total chlorine. Enough for a daily check in a pool you already know.
  • 6-way or 7-way strips add hardness and stabilizer (CYA), and some add total chlorine or bromine. Useful for a weekly look at the slow-moving numbers.
  • Stabilizer (CYA) strips read in wide steps. Use them to spot a big change, and confirm with a drop test before you add stabilizer or drain (see how to test cyanuric acid).
  • Salt strips are a separate product for salt water pools, with their own reading time. Many owners compare them with the chlorinator's display; see pool salt level.
  • Hot tub strips are made for spa ranges and often read bromine. Some pool strips work in a hot tub, but only if the chart covers spa levels; see pool chemicals in a hot tub.

Whatever you buy, check the expiration date on the bottle and buy a size you will use before it expires.

Reading between colors

Most of the time your pad will land between two blocks. Don't invent a decimal. Pick the range, and when you decide what to do, lean toward the smaller correction:

  • Chlorine between two blocks: read it as the lower one. Topping up chlorine by an extra ppm is low risk. Letting it run out is how algae start.
  • pH between 7.5 and 7.8: treat it as the lower value when you calculate acid, add that smaller dose, and retest after 30 minutes. It's easier to add a second small dose than to undo too much acid.
  • TA, CH, or CYA between blocks: these change slowly. Don't dose on a borderline strip; confirm with a drop test or a second strip from another bottle first.
  • Colors that match nothing on the chart: usually an expired or damp bottle, a late reading, or chlorine so high it bleached the pad. Retest with a fresh strip before you add anything.

Why strips and camera apps disagree

If you photograph the same strip twice and get two different answers, the strip may be fine. The camera is the problem. App Store reviews of scanner apps describe exactly this. One Clorox Pool review (August 2, 2026) says the numbers are "all over the place" for the same strip. An HTH Test to Swim review (July 10, 2026) says you can "test the same strip seconds apart and it will give you different results."

The physics explains it. A strip reads in a few steps, so a camera cannot be more precise than the chart on the bottle, even if the app prints a decimal. Phone cameras also adjust white balance and exposure on their own, wet pads reflect light, and the color keeps changing after the reading time. Brand scanner apps usually work only with that brand's strips, so if you switch strips, the app no longer applies. The honest output from any strip, read by eye or by camera, is a step or a range.

Are pool test strips accurate? Strips vs drop kits

The CDC's advice for home pools is direct: use a DPD test kit for chlorine and pH; strips can be used, but they "are less accurate than the DPD test kit." Drop kits cost more up front and take a few minutes, but they give finer numbers where it matters.

Test strips compared with a FAS-DPD drop kit
Test stripsFAS-DPD drop kit (for example Taylor K-2006)
How chlorine is readColor match against a chartCount drops until pink turns clear (titration)
Chlorine resolutionChart steps, for example 1, 3, and 5 ppm0.2 or 0.5 ppm per drop, depending on sample size (Taylor)
At high chlorine (shock)Pads bleach and read wrongStill readable: no color matching at the endpoint (Taylor)
Free vs combined chlorineSome strips have a TC pad; small gaps are hard to seeMeasures free and combined chlorine separately
Best useQuick daily check of FC and pHWeekly full test, shocking, and any time a strip is borderline

A good routine for most owners: strips for quick daily checks, a FAS-DPD kit once a week and whenever you shock or treat algae. If your strip and your drop kit disagree, trust the drop kit and check the strip bottle's date.

Enter your strip result

Pick the block that matches each pad. The calculator uses the value of the block you pick and turns it into a plan with amounts for your products. If a pad sits between two blocks, pick the one the rules above suggest. For drop-kit numbers, use the full pool chemical calculator, which accepts exact values.

Test strip calculator

Inputs
Don't know it? Use the volume calculator.

Result for example values. Enter your own numbers.

Don't swim yet

Chlorine is low. After the acid step (step 2 below), wait 30 minutes with the pump running before anyone gets in.

Your targets: FC 2.5–4 ppm (minimum 2.5 for CYA 30; 4 ppm is a common label limit), pH 7.4–7.6, TA 80–120, CYA 30–50. If your product's label lists different levels, the label wins.

1

Add chlorine

38–58 fl oz1.14–1.70 L

Pool liquid chlorine 10%

FC 1 → 4 ppm

Chlorine is below the minimum for your CYA (2.5 ppm).

Start with 38 fl oz, retest in 30 min, then add more if needed.

Strip reading: strips are less precise than drop tests. Treat results as approximate.

Wait 30 min with the pump running.

2

Lower pH: add acid

6.5–11 fl oz194–337 mL

Muriatic acid 31.45%

pH 7.8 → 7.5

pH is above 7.6.

Start with 6.5 fl oz, retest in 30 min, then add more if needed.

Strip reading: strips are less precise than drop tests. Treat results as approximate.

Retest FC and pH in 30 minutes.

Save to my pool in the app

Estimates, not guarantees. Always follow the product label. How we calculate

In the Pooldex app, entering a strip result takes five taps: choose the block for each pad. It works with any brand. A camera helper that compares your strip with the chart on your own bottle is planned for a later version. It will show the step it sees, not a made-up decimal, and you can always correct it.

Always follow the product label. It is a violation of federal law to use a pesticide product in a manner inconsistent with its labeling.

FAQ

How to read pool test strip results?

Dip the strip for the time on the bottle, hold it flat, and match each pad to the bottle's chart in the shade, before the reading time runs out. Write down each pad as the closest block, or as "between two blocks" when it falls in between, and dose from the conservative end of that range.

Are pool test strips or drops better?

Drops are more accurate, especially for chlorine: a FAS-DPD kit reads in 0.2 or 0.5 ppm steps and still works at shock levels. Strips are faster and fine for quick daily checks. Many owners use both. Kits compared side by side: the best pool test kit.

Are test strips accurate for chlorine?

Close enough for a daily check, not for fine-tuning. The free chlorine pad reads in steps such as 0, 0.5, 1, 3, 5, and 10 ppm, so a reading of "3" can mean anything between the blocks around it. Above about 10 ppm, strong chlorine can bleach the pad. The CDC says strips are less accurate than a DPD drop kit, so confirm big decisions with drops.

Sources

  • CDC, Home pool and hot tub water treatment and testing: cdc.gov
  • CDC, Model Aquatic Health Code 2024, Annex (HOCl share by pH): cdc.gov (PDF)
  • Taylor Technologies, How FAS-DPD tests for free and combined chlorine: taylortechnologies.com
  • Taylor Technologies, FAS-DPD drop test, 1 drop = 0.2 or 0.5 ppm: taylortechnologies.com
  • AquaChek, Water testing 101 (storage and expiration): aquachek.com
  • PHTA fact sheet, Sodium hypochlorite (high chlorine and test interference): phta.org
  • App Store reviews: Clorox Pool (id957130735, review of 2026-08-02) and HTH Test to Swim (id643360256, review of 2026-07-10), read 2026-09-29 via the public reviews feed.