Pool winterizing chemicals: what you need to close a pool
To winterize a pool you need a test kit, a chlorine shock dosed by its label, the balancers your test calls for (baking soda, acid, calcium), and, if you choose, a winter algaecide added after chlorine drops. Pool antifreeze is not a water chemical: it goes only into plumbing lines you haven't blown out.
Always follow your product’s label directions. Pool and spa chlorine, bromine, shock, and algaecides are EPA-registered pesticides: use products labeled for pool or spa use, and don’t swim or soak until levels are within the limit on your product’s label. If this page and a label disagree, the label wins.
Pooldex, free for iPhone: save your pool and products, get wait timers and a retest reminder, and keep a log of every test. No ads, no account. Download on the App Store
On this page (9 sections)
This page is the shopping list and the order of use. The full closing steps are on how to close an inground pool and how to close an above-ground pool. When to close is on when to open and close a pool: Hayward's guidance is once the water stays below 65 °F.
Enter your last test before closing, and the calculator plans the balancing doses in order. The shock and algaecide doses come from your products' labels.
The short list
| Product | Why | Needed? |
|---|---|---|
| Test kit (free chlorine, pH, alkalinity, calcium, and stabilizer) | Tells you which of the products below you actually need | Yes |
| Chlorine shock (liquid chlorine, cal-hypo, or dichlor) | Clears out organics and algae before the cover goes on | Yes, at the label dose for your gallons |
| Baking soda | Raises total alkalinity (TA) so pH stays steady over winter | Only if TA tests low |
| Muriatic acid or dry acid | Lowers pH or TA | Only if your test calls for it |
| Calcium increaser | Keeps cold, low-calcium water from etching plaster | Only for plaster pools that test low |
| Winter algaecide | Slows algae while the water sits unfiltered | Optional |
| Metal or stain-and-scale treatment | Keeps dissolved metals or scale from depositing | Only for well water or a history of stains |
| Pool antifreeze (propylene glycol) | Protects plumbing lines from freezing | Only in lines you don't blow out and plug, and only if your equipment maker allows it |
Hayward's closing targets: pH 7.2–7.8, total alkalinity 80–120 ppm, calcium hardness 180–220 ppm. Plaster pools often run higher calcium; see the inground closing guide.
What's in a winterizing kit
A "winterizing kit" or "closing kit" is a bundle sized for a range of gallons. Contents vary by brand, so read the label to see which of the products above it contains. Common parts are a shock, a winter algaecide, a stain-and-scale or metal treatment, and an enzyme. No kit includes a test, so a kit can add a product your water doesn't need and leave out one it does.
- Check the active ingredient and the gallon range on the box. A kit for "up to 15,000 gallons" is the wrong dose for 8,000 or 25,000.
- Check the type of shock. Dichlor and trichlor add stabilizer (CYA), which builds up over the years. Non-chlorine shock (potassium monopersulfate, MPS) breaks down organic waste but does not sanitize the water.
- Test first, then use only the parts you need. Unused products keep if stored cool, dry, and closed; see how to store pool chemicals.
Opening kits are built for start-up, and their contents differ. Read the label instead of assuming one bag does both jobs.
Order and timing
- Test free chlorine (FC), pH, total alkalinity (TA), calcium hardness (CH), and stabilizer (CYA) with the pump running. Write the numbers down: they are next spring's starting point.
- Balance alkalinity, then pH, then calcium, one product at a time with about 30 minutes of pump time between them. The calculator above gives the doses in that order.
- Shock at the label dose for your gallons, in the evening, with the pump running. The shock guide scales a label dose to your pool.
- Wait for chlorine to fall. Hayward says to add winter algaecide only after chlorine drops to 1.0–3.0 ppm, and never to add shock and algaecide at the same time.
- Add winter algaecide (optional) at its label dose, with the pump running.
- Then lower the water and winterize the lines and equipment. Antifreeze, if you use it, goes in at this step.
Winter algaecide
A winter algaecide is a longer-lasting algaecide meant to sit in still, cold water. It helps; it doesn't replace a good shock and a tight cover. Two rules from Hayward: wait until chlorine has fallen to 1.0–3.0 ppm, and never add it together with shock. For the dose, use the label: the algaecide calculator scales a label dose to your gallons. Copper-based algaecides can stain pool surfaces (a copper label we read warns about this for the full-strength product), so follow the label closely and skip them if your pool has a history of metal stains.
Pool antifreeze is for the lines
Pool antifreeze is propylene glycol, the same type used in RV plumbing. It goes into skimmer and return lines to keep leftover water in the pipes from freezing. Hayward says to add it only to lines you don't blow out, following the package directions. Never pour it into the pool itself, and never use automotive antifreeze (ethylene glycol), which is toxic.
Many owners skip antifreeze: they blow the lines dry with air and plug them. Check your pump, filter, and heater manuals before adding antifreeze near equipment. The steps are on how to blow out pool lines.
Intex and other above-ground pools
For an Intex pool that stays up for winter, Intex support says to clean and filter the water, balance it, and add "suitable winterisation chemicals" (asking a pool dealer which ones). It also says to plug the wall fittings, drain the pump and hoses, and store them indoors above 32 °F (0 °C). Intex doesn't list a branded kit with fixed contents, so the same list above applies: test, balance, shock by the label, and add an algaecide only after chlorine falls. Small pools reach high chlorine with small doses, so measure carefully.
If you take an above-ground pool down for winter, you don't need winter chemicals at all: drain, clean, dry, and store it as its manual says.
Do you need a kit at all?
You need clean, balanced water with chlorine in it when the cover goes on. Whether that comes from a kit or from separate products you already own doesn't matter. Kits are convenient; separate products let you dose only what your test shows. In climates without freezes, you may not close at all: keep the pump running fewer hours and keep testing, as described in the inground closing guide.
Seasonal note: most pools close in September and October, but the list is the same any month you close.
Safety. Never mix chlorine with acid, with algaecide in the same bucket, or with another type of chlorine. Add each product to the water separately with the pump running, and add chemicals to water, never water to chemicals. Wear gloves and eye protection. Keep leftover products locked up for winter, away from heat and moisture. Poison Control: 1-800-222-1222. Always follow the product label. It is a violation of federal law to use a pesticide product in a manner inconsistent with its labeling.
FAQ
What chemicals are needed to close an above-ground pool?
The same as for an inground pool: a test kit, a chlorine shock at its label dose, balancers your test calls for (baking soda, acid, calcium), and an optional winter algaecide added after chlorine falls to 1.0–3.0 ppm. Intex calls these "suitable winterisation chemicals" and suggests asking a pool dealer. Above-ground lines are usually unplugged and drained instead of filled with antifreeze.
Are pool winterizing chemicals necessary?
Shock and balanced water are: they keep algae and stains from setting in while the water sits. A winter algaecide is optional. A pre-packed kit is never required if you have the separate products and a test kit.
Can you put pool antifreeze in the pool water?
No. Pool antifreeze is for plumbing lines only, and only where the equipment maker allows it. Never use automotive antifreeze anywhere in a pool system.
Are pool opening and closing kits the same?
Not necessarily. Each is a bundle for one job, and contents differ by brand: a closing kit is built around shock and a winter algaecide for still water, while an opening kit is built for start-up. Read the contents and test first, whichever you buy.
How much winter algaecide should I add?
The amount on its label for your pool's gallons. Add it only after chlorine has fallen to 1.0–3.0 ppm after the shock, per Hayward, and never with shock.
Sources
- Hayward, Ten essential steps to closing your pool (closing ranges, shock by package directions, algaecide after chlorine falls to 1.0–3.0 ppm, never with shock, antifreeze in lines): hayward.com
- Hayward, The right time to close your pool (below 65 °F): hayward.com
- Hayward, Closing your pool (cold and mild climates): hayward.com
- Intex Support, Getting the pool ready for winter (winterization chemicals, plugs, pump stored above 0 °C): intexsupport.com
- CDC, Store pool chemicals safely (poster): cdc.gov (PDF)